Call Today:  503-895-0242
You're a Go with GoFlight
Contact Us

Blog

Connecting the GF-DIO Board

Now the GF-DIO Board must be connected to the computer. With the provided USB cable, simply plug the appropriately matching ends into both the GF-DIO Board’s USB slot and any non USB 3 port on the computer case.  Once the GF-DIO board is completely connected to the computer, it is ready to be configured for… read more

Connecting the Hardware to the GF-DIO Board

The GF-DIO Board comes with 88 positions for components to be added. Each position is a made up of a 3-pin connection. Once the hardware components are plugged into the wire assembly, plug the other end of the wire assembly into one of the positions on the DIO board, taking note of the number position… read more

Installing and Configuring the GF-P8

Installing GF-Config for the GF-P8 Module 1. Get on line and go to  www.goflightinc.com. 2. On the GoFlight home page click Support. 3. Click on “GF Config x.xx” to download the latest module drivers and configuration software. 4. Click “Run” or “Save” and follow the instruction to install the software.  If the software installer detects… read more

Configuring the GF-TQ6

Main Control Lever Calibration After connecting the GF-TQ6 to your computer for the first time, it is necessary to calibrate the six main control levers so that they have effect throughout their entire range of motion. After this process has been completed, you will not have to repeat the calibration steps unless you: (a) wish… read more

Configuring the GF-MCP Pro

Using GF-Config, you can change certain characteristics of the MCP Pro’s operation, so that it can operate most realistically with different types of aircraft. You select the MCP Pro for configuration by left clicking on its icon in the left-hand portion of the GF-Config window. Once the MCP Pro is selected for configuration, you can… read more

Configuring the GF-WP6

To select the functions that you want your GF-WP6 to perform, you choose selections from function lists presented in the Configuration View, the right-hand panel in the GFConfig program window. The Configuration View presents a tab control for each flight simulator program that is detected on your computer. When selecting functions for the GF-WP6, Make… read more

Configuring the GF-MESM

To Setup your GF-MESM for the default aircraft. In GF-Config use the cockpit function menu. Example: Click on LStart knob turn CCW “Counter Clockwise” and set the cockpit function to ENG_1_Starter_off. Then click on LStart knob turn CW “Clockwise” and set the cockpit function to ENG_1_Starter_on Repeat the process for the Right engine starter knob…. read more

Configuring the GF-DIO Board

Now that the GF-DIO Board is connected to the computer it is ready for configuration. Turn on the computer and start the GF-Config program. GF-Config starts up with a picture of all the connected GoFlight modules available for configuration. Select the image of the GF-DIO Board in the left window of the program. On the… read more

Configuring the GF-166

To select the functions that you want your GF-166 to perform, you choose selections from function lists presented in the Configuration View, the right-hand panel in the GF-Config program window. The Configuration View presents a tab control for each flight simulator program that is detected on your computer. When selecting functions for the GF-166, make… read more

Configure the GF-DIO with Keystrokes

If configuring the GF-DIO Board through key strokes is preferred, this too can be done through GF-Config. Start by flipping the desired switch to be programmed. Then select Key Sequence in the Input Function 1 Box in the GF-Config program. Now use the keyboard to set the keystrokes for the switch. The screenshot below shows… read more

Phone:
503-895-0242
Tech Support:
Tech Support: 503-688-7921
Address:
163 SW Freeman Avenue
Suite B
Hillsboro, Oregon 97123
Designed & Created by Pegasus Online